1. Precautions for use

Pressing, squeezing, bumping, falling and smashing are taboo

Pressure, squeeze, touch is easy to be ignored in most of the users in the use of the usual three o 'clock, and fell and hit are not common, after all, no one will take so precious when plank brick thrown, screen is made up of multilayer reflector, reflector, filter plate and protective film, and the material is very fragile and easily damaged, So once the external force on its stool will cause irreparable damage to the screen, such as display fuzzy, water ripples and other phenomena, thus affecting the display output effect. If that's what caused the screen to crack.

2. Maintenance and maintenance

Soft cloth + water

Monitor in use after a period of time will be contaminated with a lot of dust on the screen, in order to monitor the screen clean, as a user needs to regularly wash its face, but this face but pay attention to yo. At this time, there is often some dust on the screen, so it is easier to clean up. All you need to do is gently wipe off the dust with a soft damp cloth. Be careful that the cloth is not too rough, or it will bruise the screen. In addition to the soft cloth to wring dry, because water is the natural enemy of the display. Dry the wet mark after cleaning.

3. Avoid displaying the same image for a long time

LCDS, like other types of displays, can cause their innards to age or burn out over long periods of time, especially if they display the same picture for a long time. If one type of fixed content is displayed continuously for a long time, it is possible to cause some pixels to overheat, which in turn causes internal burn, producing bad spots. The damage is irreversible and cannot be repaired. So when we use it, we should be careful to turn off the monitor when there is nothing to do, and if it is only temporary, choose a screen saver, or turn down the brightness of the monitor a bit.

4. Use the recommended best resolution

The principle of display is one-to-one display. Under the optimal resolution of the display will display card output analog display signal into a display signal with specific address information, and then into the LCD panel, the display signal will be directly added to the corresponding pixel on the drive tube. For such point-to-point output situations, it is certainly important to use the best resolution recommended by the monitor.

5. Avoid burning inside the screen

While enjoying the high-grade display effect of the monitor every day, do not forget to maintain this important link. Monitor only good maintenance, to be able to long-term trouble-free service for users. It is well known that leaving LCD monitors on for long periods of time reduces their life. Therefore, in order to avoid this kind of situation, the following measures can be adopted when not in use:

(1) turn off the monitor as far as possible when not in use (2) change the display content on the screen frequently at different intervals (when watching movies, if you leave the screen do not pause in the original picture, can be minimized, and then use dynamic wallpaper) (3) adjust the brightness of the screen to a relatively low level

6. Do not attempt to remove the monitor

This is not only the maintenance of the screen, but also the protection of users. Display shut down for a long time, on the back of the components of CFL inverter still may have about 1000 v high voltage, the high pressure for the human body is very dangerous, so don't attempt to remove or change the display, so as not to be hurt in addition without permission of the maintenance and change will likely lead to display even temporarily cannot work, if there is any fault, It is strongly recommended to get a professional repair station for repair.

7. Maintain ambient humidity

The general humidity is maintained at 30%~80% display can work normally, but once the indoor humidity is higher than 80%, the display will produce condensation phenomenon. The internal power transformer and other coils are also prone to leakage after damp, and may even cause a short circuit; And the high voltage part of the display is easy to produce discharge phenomenon do not let any wet things into the display, if the display has been invaded by moisture, must disconnect the power supply as soon as possible, the display is placed in a warm and dry place, so that the timely evaporation of water, and then can open the power supply. Add electricity to the wet display, easy to lead to corrosion of the liquid crystal electrode, and then irreversible damage.

8. Avoid unnecessary shaking

Display can be said to be recognized as a sensitive peripheral, it contains a considerable proportion of sensitive glass electrical components, so that the screen is very fragile, to avoid strong impact and vibration, otherwise it is easy to lead to the display screen and CFL unit damage. Don't have to pay special attention to point fingers on the screen, otherwise, after a long time there will be a bad point, or color is not natural for display as many essential electronic products, users work most of the time to face it, thus protect the screen is a very worthy of your attention, if you can do it in the usual use of the above points, Then the service life of the display will also increase.